HP color laser printer repair maintenance code
Summary of HP color laser printer maintenance code
PAPER JAM error code common fault summary
:13-1 PAPER JAM or 13,2 PAPER JAM paper feed part is delayed or stopped.
Lifting method to 1) determine the tray has been installed correctly;
2) determine whether the paper part of the no obstruction;
3) Check PS402 and PS403 is normal, necessary, need to replace sensor.
13,5 PAPER JAM or 13.6 PAPER JAM paper in the fuser section is to delay or stop.
Lifting method) to determine the transfer roller and transfer belt to work properly;
2) to determine the feeding path has no obstructions;
3) Check the PS1307 is working properly, when necessary, replace the sensor
13,10 PAPER JAM paper suction paper has been delayed or stuck
Lifting methods: 1) check the feed part of the feeder obstructions;
2) Check the feeder in the PS1701, PS1703 sensor is reset, if necessary, replace sensors
13, 20 PAPER JAM or 13,21 PAPER JAM paper is stuck in the paper path or the top cover is open.
Lifting methods: 1) Check the entire paper path clear of obstructions;
2) Check all of the feed component is reset (including whether the cover above);
3) Check the paper path all the sensor is reset in need of replacement, if necessary,
The 20 INSUFFIENT the MEMORY printer to accept too much data, beyond the scope of the printer's memory.
Lifting method 1) Press [GO] button, to continue printing (some print content may be lost);
2) To increase the printer memory
21 PAGE TOO COMLEX is too complex to print content.
Lifting methods: 1) Press the [GO] button to continue printing (some of the print content may be lost);
2) PAGE PROTECT value is set to AUTO
22 EIOХBUFFER OVERFLOW is too much data to the designated EIO peripherals.
Lifting method: press [GO] button to clear this information (transmission data will be lost)
13,5 PAPER JAM or 13.6 PAPER JAM paper in the fuser section is to delay or stop.
Lifting methods: 1) determine the transfer roller and transfer belt to work properly;
2) to determine the feeding path has no obstructions;
3) Check the PS1307 is working properly, when necessary, replace the sensor
13,10 PAPER JAM Paper is delayed or stuck suction paper.
Lifting method 1) Check the feeder feed part of obstructions;
2) Check the feeder in the PS1701, PS1703 sensor is reset, if necessary, replace sensors
13, 20 PAPER JAM or 13,21 PAPER JAM paper is stuck in the paper path or the top cover is open.
Lifting methods: 1) Check the entire paper path clear of obstructions;
2) Check all of the feed component is reset (including whether the cover above);
3) Check the paper path all the sensor is reset in need of replacement, if necessary,
The 20 INSUFFIENT the MEMORY printer to accept too much data, beyond the scope of the printer's memory.
Lifting methods: 1) Press the [GO] button to continue printing (some of the print content may be lost);
2) To increase the printer memory
21 PAGE TOO COMLEX is too complex to print content.
Lifting methods: 1) Press the [GO] button to continue printing (some of the print content may be lost);
2) PAGE PROTECT value is set to AUTO
22 EIOХBUFFER OVERFLOW is too much data to the designated EIO peripherals.
To lift press the [GO] button to clear this information (the transmission of data will be lost)
50, the ERROR FUSER fuser error, laser printers, software and hardware solutions, its value is expressed as follows:
A heating temperature is low
Fuser warm-up protection
3 heating temperature is too high
4 power supply voltage instability
5 fuser does not match
Lifting methods: one, turn the power off 20 minutes before turning on power;
2, re-install the heating component;
Turn off the power, remove the fuser, check the J1307 and J1307-2 J1308-1 and J1308-2-1 the same, such as unreasonable, the replacement of the other hot components.
51, * PRINTER the ERROR laser scanning errors * values ??are expressed as follows:
A laser detection error
Laser error
Lifting methods: a re-start;
2 re-install the laser and associated cables;
Replace the laser error code * PRINTER ERROR Fault Summary
52, the ERROR * PRINTER laser scanning speed does not match the * value is expressed as follows:
A scan start error
2 scan rotation error
Lifting methods: a re-start;
2 re-install the laser and associated cables;
3 replace the laser
53, XY, ZZPRINTER ERROR additional memory errors, of which the meaning of XYZ are as follows:
X = DIMM type
0 = ROM
1 = RAM
Y = device location
1-3, said the wrong memory slot location
ZZ = Error Number
0 = do not support the installed memory
1 = not compatible with the installed memory
2 = does not support the installed memory model
3 = RAM test fails
4 = more than the range of the maximum amount of RAM
5 = more than the range of maximum ROM
6 = Invalid DIMM speed
7 = the DIMMs reported error signal
8 = DIMM RAM parity error
9 = ROM address mapping error
10 = DIMM address conflict
11 = the PDC XROM out of range
12 = unable to complete the memory buffer
Lifting methods: 1 Turn off the power, the development of digital color printing and offset printing knowledge, skills, and re-install the insert memory;
2 exchange into the memory location;
3 to replace a false memory
55 PRINTER ERROR is an internal communication error
Lifting methods: 1, check the power position
2, replace the interface board
3, replace the DC control board
56 * PRINTER ERROR temporary printing error * value indicates that:
An incorrect input or error additional equipment to be connected
2, the incorrect output
Lifting methods: 1, restart the printer;
2, check the printer configuration;
3, correction connect additional devices
57 PRINTER ERROR fan error
Lifting methods: 1, check the printer fan is the right of access and whether obstructions stuck;
2, replace the fan
59, the ERROR * PRINTER motor error * values ??are expressed as follows:
0 motor error
A motor startup error
Two motor running error
Lifting methods: 1, restart the printer;
2 to determine the connecting gear to normal operation;
Sure to connect the motor cable is correctly inserted
4, replace the motor
62, the ERROR * PRINTER printer memory error * values ??are expressed as follows:
0 = internal memory
1-3 = DIMM slots 1-3
Release method: a re-install the insert memory;
2, the exchange installation location;
3, the replacement of the inserted memory
64 PRINTER ERROR accept the error of the data buffer
Lifting methods: 1, restart the printer;
2, replace the interface board
66 of XX, YY PRINTER ERROR external misfeeds, XY described as follows:
The device number to use 1STX = 2NDX ??= device type:
A) the input device
B) output device
C)-packing / binding equipment YY = Error number of the equipment
Lifting methods: 1, restart the printer;
2, check all the connecting cables;
3, re-install an external feed equipment
79 PRINTER ERROR printer detects an error
Lifting methods: 1, restart the printer;
2, whether the judgment used by the printing software and printer to match;
3, the replacement of the transmission cables and power supply;
4 Remove the DIMM
5, if possible, the use of parallel ports transfer data;
6, removal of the EIO equipment;
7, replace the interface card...
PAPER JAM error code common fault summary
:13-1 PAPER JAM or 13,2 PAPER JAM paper feed part is delayed or stopped.
Lifting method to 1) determine the tray has been installed correctly;
2) determine whether the paper part of the no obstruction;
3) Check PS402 and PS403 is normal, necessary, need to replace sensor.
13,5 PAPER JAM or 13.6 PAPER JAM paper in the fuser section is to delay or stop.
Lifting method) to determine the transfer roller and transfer belt to work properly;
2) to determine the feeding path has no obstructions;
3) Check the PS1307 is working properly, when necessary, replace the sensor
13,10 PAPER JAM paper suction paper has been delayed or stuck
Lifting methods: 1) check the feed part of the feeder obstructions;
2) Check the feeder in the PS1701, PS1703 sensor is reset, if necessary, replace sensors
13, 20 PAPER JAM or 13,21 PAPER JAM paper is stuck in the paper path or the top cover is open.
Lifting methods: 1) Check the entire paper path clear of obstructions;
2) Check all of the feed component is reset (including whether the cover above);
3) Check the paper path all the sensor is reset in need of replacement, if necessary,
The 20 INSUFFIENT the MEMORY printer to accept too much data, beyond the scope of the printer's memory.
Lifting method 1) Press [GO] button, to continue printing (some print content may be lost);
2) To increase the printer memory
21 PAGE TOO COMLEX is too complex to print content.
Lifting methods: 1) Press the [GO] button to continue printing (some of the print content may be lost);
2) PAGE PROTECT value is set to AUTO
22 EIOХBUFFER OVERFLOW is too much data to the designated EIO peripherals.
Lifting method: press [GO] button to clear this information (transmission data will be lost)
13,5 PAPER JAM or 13.6 PAPER JAM paper in the fuser section is to delay or stop.
Lifting methods: 1) determine the transfer roller and transfer belt to work properly;
2) to determine the feeding path has no obstructions;
3) Check the PS1307 is working properly, when necessary, replace the sensor
13,10 PAPER JAM Paper is delayed or stuck suction paper.
Lifting method 1) Check the feeder feed part of obstructions;
2) Check the feeder in the PS1701, PS1703 sensor is reset, if necessary, replace sensors
13, 20 PAPER JAM or 13,21 PAPER JAM paper is stuck in the paper path or the top cover is open.
Lifting methods: 1) Check the entire paper path clear of obstructions;
2) Check all of the feed component is reset (including whether the cover above);
3) Check the paper path all the sensor is reset in need of replacement, if necessary,
The 20 INSUFFIENT the MEMORY printer to accept too much data, beyond the scope of the printer's memory.
Lifting methods: 1) Press the [GO] button to continue printing (some of the print content may be lost);
2) To increase the printer memory
21 PAGE TOO COMLEX is too complex to print content.
Lifting methods: 1) Press the [GO] button to continue printing (some of the print content may be lost);
2) PAGE PROTECT value is set to AUTO
22 EIOХBUFFER OVERFLOW is too much data to the designated EIO peripherals.
To lift press the [GO] button to clear this information (the transmission of data will be lost)
50, the ERROR FUSER fuser error, laser printers, software and hardware solutions, its value is expressed as follows:
A heating temperature is low
Fuser warm-up protection
3 heating temperature is too high
4 power supply voltage instability
5 fuser does not match
Lifting methods: one, turn the power off 20 minutes before turning on power;
2, re-install the heating component;
Turn off the power, remove the fuser, check the J1307 and J1307-2 J1308-1 and J1308-2-1 the same, such as unreasonable, the replacement of the other hot components.
51, * PRINTER the ERROR laser scanning errors * values ??are expressed as follows:
A laser detection error
Laser error
Lifting methods: a re-start;
2 re-install the laser and associated cables;
Replace the laser error code * PRINTER ERROR Fault Summary
52, the ERROR * PRINTER laser scanning speed does not match the * value is expressed as follows:
A scan start error
2 scan rotation error
Lifting methods: a re-start;
2 re-install the laser and associated cables;
3 replace the laser
53, XY, ZZPRINTER ERROR additional memory errors, of which the meaning of XYZ are as follows:
X = DIMM type
0 = ROM
1 = RAM
Y = device location
1-3, said the wrong memory slot location
ZZ = Error Number
0 = do not support the installed memory
1 = not compatible with the installed memory
2 = does not support the installed memory model
3 = RAM test fails
4 = more than the range of the maximum amount of RAM
5 = more than the range of maximum ROM
6 = Invalid DIMM speed
7 = the DIMMs reported error signal
8 = DIMM RAM parity error
9 = ROM address mapping error
10 = DIMM address conflict
11 = the PDC XROM out of range
12 = unable to complete the memory buffer
Lifting methods: 1 Turn off the power, the development of digital color printing and offset printing knowledge, skills, and re-install the insert memory;
2 exchange into the memory location;
3 to replace a false memory
55 PRINTER ERROR is an internal communication error
Lifting methods: 1, check the power position
2, replace the interface board
3, replace the DC control board
56 * PRINTER ERROR temporary printing error * value indicates that:
An incorrect input or error additional equipment to be connected
2, the incorrect output
Lifting methods: 1, restart the printer;
2, check the printer configuration;
3, correction connect additional devices
57 PRINTER ERROR fan error
Lifting methods: 1, check the printer fan is the right of access and whether obstructions stuck;
2, replace the fan
59, the ERROR * PRINTER motor error * values ??are expressed as follows:
0 motor error
A motor startup error
Two motor running error
Lifting methods: 1, restart the printer;
2 to determine the connecting gear to normal operation;
Sure to connect the motor cable is correctly inserted
4, replace the motor
62, the ERROR * PRINTER printer memory error * values ??are expressed as follows:
0 = internal memory
1-3 = DIMM slots 1-3
Release method: a re-install the insert memory;
2, the exchange installation location;
3, the replacement of the inserted memory
64 PRINTER ERROR accept the error of the data buffer
Lifting methods: 1, restart the printer;
2, replace the interface board
66 of XX, YY PRINTER ERROR external misfeeds, XY described as follows:
The device number to use 1STX = 2NDX ??= device type:
A) the input device
B) output device
C)-packing / binding equipment YY = Error number of the equipment
Lifting methods: 1, restart the printer;
2, check all the connecting cables;
3, re-install an external feed equipment
79 PRINTER ERROR printer detects an error
Lifting methods: 1, restart the printer;
2, whether the judgment used by the printing software and printer to match;
3, the replacement of the transmission cables and power supply;
4 Remove the DIMM
5, if possible, the use of parallel ports transfer data;
6, removal of the EIO equipment;
7, replace the interface card...
