HP 5000 C30D-C4002A/03A PartsOct 28,2012 PartDescription56220006KTPC_Board - EIGS controller boardC4015ADeveloper - Developer unit - Toner cartridge installs into this unit61030058KTMaintenance_Kit - Maintenance kit - Replacement parts after 1 million pagesC4675AFuser_Assembly - Fuser Assembly (100-127v) - Bonds toner to paper by heat55020014KTPC_Board - PCL board for HP 5000 C3062020046KTPC_Board - Control panel PC board - Does NOT include housing or overlay11000249KTRoller - Lower pickup roller assembly - For lower paper input trayJ2590APrint_Server - External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and 3 parallel (DB-25) output connectors60020004KTPC_Board - Output control boardC4011ACleaner - Cleaner unit - Main charger slides into center of this unitJ3264APrint_Server - HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to a token ring (DB-9 or RJ-45) LAN55020594KTGear - Duplex drive gear assembly53020090KTMotor - Elevator gear assembly - Includes motor, worm gear, belt, pulley and drive gear53020141KTMotor - Slide assembly - Includes 2 jogging motors and jogging block55020214KTMotor - 'C' stepper motor assembly - Includes duplex registration motor, duplex route solenoid, and timing belt51020866KTMotor - Main drive motor61020336KTRoller - Timing roller assembly - Paper feed belt is routed around this shaft/roller assembly and the upper and lower paper feed rollers73820027KTJob_Offset - Job offset assembly11000130KTDrive_Assembly - 1.44MB 3.5-inch floppy drive11000246KTRoller - Feed roller assembly - For upper paper input tray61020023KTTransport_Module - Vacuum transport assembly - Includes rollers, belts, and blower motor with speed sensor60020005KTPC_Board - Input control board53020124KTPower_Supply - HCI/O power supply61020072KTPrint_Server - Signal interface board - Has serial/parallel I/O connectors61020022KTPower_Supply - High voltage power supply55020020KTPC_Board - Duplex control board (#1)51020057KTDrive_Assembly - Cleaner unit drive assembly - Gear/idler arm assembly that one end of the cleaner drive belt is routed around61020150KTCorona - Transfer Corona assembly - Installs into the upper/lower paper guide assembly51020056KTDrive_Assembly - Fuser drive assembly - Geared assembly that is found by opening rear cover of printer and looking in the upper left corner55020260KTRoller - Duplex feed rollerJ4101BModule - HP JetDirect 300X external print server module (10Base-T and 100Base-TX) - Connects between printer parallel port and LAN networkJ2591APrint_Server - External JetDirect LAN interface module and power module - Has EtherTwist (10Base-T) and ThinLAN (10Base-2) connectorsJ4101-61011Print_Server - External JetDirect LAN interface module with EtherTwist 10Base-T/100BaseTX connector51020062KTRoller - Exit pinch roller assembly - Includes static brush51020088KTPC_Board - Power control boardJ2383-61005Module - External token ring interface module - Has DB-9 connector55020248KTSolenoid - Duplex route separator paper exit solenoid54020058KTDoor - Front door assembly - Part of 1200 sheet paper input unit - Open this door to access paper loading tray61020320KTRoller - Feed roller assembly - For lower paper input tray21421333KTSensor - Sensor assembly - Senses size of paper53020183KTArm - Stacker arm assembly51020682KTFan - Main cooling fanJ4102BModule - External JetDirect LAN interface module with EtherTwist (10Base-T) connectorJ3258BPrint_Server - External JetDirect 170X LAN interface module - Interfaces a parallel printer to an ethernet 10Base-T (RJ-45) LAN54020061KTSensor - 'B' sensor assembly54020284KTSensor - 'A' sensor assembly51020058KTCounter - Usage counter - Reflects number of pages printed21423825KTMotor - Toner supply motorD2975-69001Memory - 8MB, 70nS, 36-bit parity SIMM memory module53020095KTMotor - Elevator motor assembly54020053KTActuator - 'C' actuator assembly55020026KTSolenoid - Duplex feed roller solenoidJ3258-61021Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connectorC2991ACable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 3.0m (10ft) long0950-2623Power_Supply - Switching power supply (Delta DPS-158ABA) - 100-240VAC input, 47-63Hz - Four DC outputs (5.15V, +12V, -12V, 24V) - 158 watts.51020018KTLamp - Erase lamp assembly51020089KTPC_Board - Jogging motor power control board55020022KTRoller - Duplex feed roller - Shaft with two rollers - Installs on left side of front edge of main top coverJ4102-61021Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connector53020088KTSensor - HP Sensor for LaserJets51020629KTRoller - Upper paper guide roller - Shaft/roller that is part of the upper/lower paper guide assemblyC2990ACable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 1.8m (6ft) long8120-6302Power_Cord - 'Daisy chain' power cord (Dove Gray) - 18 AWG, 1.2m (4.0ft) long - Has C14 (M) plug for power input and C13 (F) plug for power outputJ3265-69001Print_Server - External JetDirect LAN interface module with EtherTwist (10Base-T and ThinLAN) (10Base-2) input connectors and three parallel (DB-25) output connectorsJ2591-69001Module - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors51020497KTRoller - Exit roller assembly - Shaft with gear on right side and five rollers on the shaftJ3258-61041Module - External JetDirect 170X LAN interface module - Interfaces a parallel printer to an ethernet 10Base-T (RJ-45) LAN21421209KTSensor - Sensor assembly - Senses size of paperJ4102-69022Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connectorJ2593-69001Module - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) input connectors and three parallel (DB-25) output connectors0950-2372Power_Module - Power supply module - 100-240VAC input, 47-63Hz, requires separate AC power cord - 5VDC output, 1A, 5 watts51020372KTSensor - Paper exit sensor - Senses when paper jams have occured21421962KTSwitch - Rear interlock switch - Part of AC power supply - Activated when rear cover is opened21420515KTSwitch - Front interlock switch - Part of AC power supply - Activated when front cover is opened55020024KTBelt - Duplex timing beltJ2382-69003Module - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors51020077KTSensor - Out tray full sensor - Senses when paper out tray is fullRG5-3579-020CNTransfer_Assembly - Transfer Roller AssemblyJ2594-69001Module - External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors21420412KTBelt - Fuser drive belt51020072KTBelt - Cleaner unit drive belt5188-5673Power_Supply - Power module (wall mount, MEI-AH ED12007) - Input voltage 230VAC, 47/53Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Europe and Israel)21421937KTSwitch - Switch - Detects if paper input tray is installed53020194KTBrush - Antistatic brush - Eliminates static charge on paper54224034KTLever - Replacement paper size lever (is NOT the original color) - For selecting size of paper in the input unit53020069KTBelt - Timing belt for the high capacity input/output unit53020031KTActuator - A' actuator assembly53020032KTActuator - 'B' actuator assembly21420401KTDrive_Assembly - Pickup roller drive assembly - Dual/cluster gear assembly that meshes between pickup and feed roller assemblies8120-2104Power_Cord - Power cord (Mint Gray) - 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Switzerland)21420413KTBelt - Paper feed drive belt0957-2192Power_Supply - Power supply module - 209-253VAC input, 47-53Hz - 13VDC output, 800mA (Europe and Israel)9100-5176Power_Module - Pwer supply, 13v/300ma jpnJ2592-69001Module - External JetDirect LAN interface module with EtherTwist (10Base-T) connector55020491KTPlug - Strapping plug - Configures AC power supply for 240V input55020489KTPlug - Strapping plug - Configures AC power supply for 220V input55020490KTPlug - Strapping plug - Configures AC power supply for 230V input51020342KTGear - Exit (Eject) gear55020482KTPlug - Strapping plug - Configures AC power supply for 120V input55020052KTRoller - Pinch roller - Part of upper/lower paper guide assembly8120-1369Power_Cord - Power cord (Mint Gray) - 17 AWG, 2.0m (6.6ft) long - Has straight (F) receptacle (for 240V in Australia, New Zealand, and China)D2974-63001Memory - 4MB, 70nS, 36-bit parity SIMM memory module21421610KTStrap - Support strap - For right side of front cover51220072KTStrap - Support strap - For left side of front cover0950-3354Power_Module - Wall mount power supply module (MEI-AH ED12010) - 220-250VAC input, 47-53Hz - 13VDC output, 800mA, 10.4 watts (South Africa)0957-2229Power_Supply - Power module (wall mount)- Input voltage 220-250VAC, 47/53Hz - Output voltage 13VDC, 800mA, 10.4W (Worldwide)C2950ACable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long0957-2197Power_Module - Wall mount power supply module - 120VAC input, 60Hz - 12VDC output, 1.0A - United States and Canada0957-2228Power_Supply - Power module (wall mount) - Input voltage 120VAC, 60Hz - Output voltage 12VDC, 1.25A, 15 watts (USA and Canada)0950-3169Power_Module - Power supply module - 110-127V AC 57-63Hz input - 13V DC output at 300mA (USA and Canada)J2590-69001Module - External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and three parallel (DB-25) output connectors5188-5676Power_Module - Power module (wall mount) - Input voltage 100VAC, 47/63Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Japan)5188-6700Power_Module - Universal AC power adapter - wide-range, 40c - Requires separate country-specific power cord8120-4753Power_Cord - Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 100V in Japan)5063-1256Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long0950-3352Power_Module - Wall mount power supply module (MEI-AH ED12010) - 100VAC input, 47-63Hz - 13VDC output, 800mA, 10.4 watts (for use in Japan)8120-1351Power_Cord - Power cord (Mint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 240V in the UK, Hong Kong, Singapore, Malaysia, and Brunei)8120-1378Power_Cord - Power cord (Jade Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 120V in USA, Canada, Latin America, Korea, Taiwan, Thailand, Spain, Brazil, and Vietnam)0950-3172Power_Module - Power supply module - 240VAC input, 47-53Hz - 13VDC output, 300mA (Australia)0950-3350Power_Module - Wall mount power supply module (Leader Electronics 48130625HK) - 200VAC input, 48-52Hz - 13VDC output, 625mA (Hong Kong)0950-3171Power_Module - Power supply module - 220-240VAC input, 47-53Hz - 13VDC output, 300mA (U. K. and Hong Kong)8120-1689Power_Cord - Power cord (Mint Gray) - 17 AWG, 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Europe, Bangladesh, Indonesia, Pakistan, Burma, Sri Lanka, and Vietnam)8120-2956Power_Cord - Power cord (Mint Gray) - 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Denmark)C2951ACable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long21420894KTBelt - Vacuum transport beltC4014ATray - HP 5000C Series Paper input trayC4676AFuser_Assembly - Fuser Assembly (200-240v) - Bonds toner to paper by heatC4679ADrive_Assembly - 170MB hard disk drive - For font storage0957-2194Power_Supply - Wall mount power supply module (MEI-AH ED12009) - 220VAC input, 47-63Hz - 13VDC output, 800mA, 10.4 watts (South Korea)51020795KTPrinthead - LED printhead assemblyC4007ACartridge - Toner cartridge (8 pkg) - Prints approximately 17k pages per cartridge at 4% average page coverage, normal densityC4682APhotoConductor - Photoconductor assembly - Includes main charger and ozone filterC4002A-ManualService_Guide_PH - HP LaserJet 5000 C30D-C4002A/03A Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams.C4006ACartridge - Toner cartridge (2 pkg) - Prints approximately 17k pages per cartridge at 4% average page coverage, normal density55030024KTPower_Supply - AC power supplyJ3265GPrint_Server - HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45), 10Base2 (BNC), or 100Base-TX (RJ-45) LAN61020323KTRoller - Upper pickup roller assembly - For upper paper input tray61020028KTDrive_Assembly - Main drive assembly (50Hz) - Geared assembly that fuser drive and cleaner unit drive belts are routed around61020013KTDrive_Assembly - Main drive assembly (60Hz) - Geared assembly that fuser drive and cleaner unit drive belts are routed aroundD3577AMemory - 8MB, 70nS, 36-bit parity SIMM memory moduleC4002ALaserJet - HP 5000 C30D-C4002A/03A PrinterD2974AMemory - 4MB, 70nS, 36-bit parity SIMM memory module61020281KTPower_Supply - DC power supply assembly51020874KTLubricant - Molycote grease - Used to lubricate printer51020875KTLubricant - Red grease - Used to lubricate printer51020876KTLubricant - Machine/gear oil - Used to lubricate printer54020125KTBelt - Timing belt for HP 5000 C3055020025KTBelt - Duplex timing belt Previous HP Digital Sender 8100C PartsNext HP Mopier 240 Parts